Noctua NA-HC1 chromax.Black.swap, Heatsink Cover for NH-U12S, NH-U12S TR4-SP3, NH-U12S DX-3647 & NH-U12S SE-AM4 (Black)
-
Alec
> 3 dayHave a mid tower case with a flat side panel? This probably wont fit. I had to trim mine down a bit in order to fit, and even then its still in contact with my glass side panel.
-
ycbmbatt
> 3 dayvery dedicated，beautiful product
-
ML
> 3 dayBought both audio and USB cables but decided to send them back in one package and label. However, I only got a refund for one while the other one like I did not sent it back. Cables seem good but wires at the end were not fully sleeved, as I expected the whole cable is sleeved and heat shrink wrapped from end to end.
-
Brent
> 3 dayFits perfectly on my noctua u12a! And if you have nzxt 510i case like I have it’s gonna be a tight fit.
-
Antony Steele
> 3 dayAs per the usual Noctua standards, the Noctua Heatsink cover was well packaged, well engineered, and had great instructions for installation. I have to say that it simply looks great on the Heatsink, and it gives the heatsink a much more finished kind of look. It is very easy to install. The sides of the shroud that cover the sides of the heatsink fit fine and still fit flush despite the fan clips being underneath. You will have to remove the shroud to remove the fan, and the fan clips. If you feel creative enough, there is enough room at the top of the shroud to install an LED or RGB LED light strip underneath the shroud, and to replace the colored inserts with a hand cut white translucent plastic insert, (think plastic coffee can lid), and run the wire to the Motherboard, and synch it up with a Motherboard RGB LED. Now you have a genuine Noctua RGB LED heatsink cover.
-
Kaiga
> 3 daynot much to say other than it does cover it nicely and was very easy to put on.
-
Maor
> 3 dayNothing much to say, it is what it is, makes the cooler look nice.
-
Neil Wilkes
Greater than one weekAdd just a nice little touch, but costs a lot for what it is
-
Colton Boehm
> 3 dayThis cover looks pretty good when its installed. I did bend the arms a little to give it a tighter fit, but otherwise its easily attached. It also seems a little expensive for what it is.
-
Josh
> 3 dayeasy install, looks great!
The NA-HC1 chromax.black.swap heatsink cover is an add-on accessory for Noctua’s award-winning NH-U12S, NH-U12S TR4-SP3, NH-U12S SE-AM4 and NH-U12S DX-3647 CPU coolers. Made from high-quality aluminium with black powder-coating finish and including swappable inlays in black, white, red, blue, green and yellow, it allows users to colour-customise the cooler in order to coordinate it with popular build colour schemes such as all black, black and white or black and red. Thanks to the easy, straightforward installation, changing the looks of your NH-U12S cooler only takes a few minutes and doesn’t even require taking it off the CPU. Combined with the chromax.black.swap edition NF-F12, fan, the NA-HC1 gives you endless possibilities to design your very own, individual NH-U12S that looks just as great as it cools!
|
|
|
|
|
|---|---|---|---|
High-quality powder-coated aluminiumTired of flimsy, thin plastic faceplates? The chromax line heatsink covers are made from sturdy, 1mm-thick aluminium and feature a scratch-resistant powder-coating finish in order to match the build quality of your Noctua heatsink. |
Match with industrialPPC or chromax fans and padsNoctua’s chromax line heatsink covers are a perfect match for the black industrialPPC and chromax.black.swap fans, both of which can be colour-customised using chromax anti-vibration pads and cables (available in black, white, red, blue, green and yellow). |
Easy installationInstalling Noctua’s chromax line heatsink covers is child’s play: Put the fixture on top of the cooler, secure it with the steel clip, slide on the cover until the magnets snap into place – done! You don’t even have to remove the cooler from the CPU or take off the fan. |
Endless options for customisationDo you want to give your entire heatsink a custom colour to take things one step further? While spray-painting heatsinks is difficult and reduces performance, Noctua’s powder-coated chromax covers can easily be repainted with custom colours and decorations. |
The NA-HC1 chromax.black.swap comes with swappable inlays in black, white, red, blue, green and yellow that allow colour-coordinating the heatsink with most popular build colour schemes. Whether you’re designing your dream machine for the years to come or switch parts on a monthly basis, matching colours has never been so easy!
Scope of delivery
- NA-HC1 chromax.black.swap heatsink cover
- Swappable inlays (red, blue, green, yellow, black, white)
Cooler Compatibility
- NH-U12S
- NH-U12S SE-AM4
- NH-U12S TR4-SP3
- NH-U12S DX-3647
Please Note:
This cover will increase the height of the heatsink by 6mm (from 158 to 164mm) and the total width by 3mm (from 125mm to 128mm). Please make sure that your case offers sufficient clearance and that the cover doesn’t make contact with any other components such as PCIe cards!
Specifications:
- Colour: black with swappable inlays (red, blue, green, yellow, black, white)
|
|
|
|
|
|
|
|---|---|---|---|---|---|---|
| NF-F12 PWM chromax.black.swap | NF-A14 PWM chromax.black.swap | NA-SAVP1 chromax.black | NA-SAV2 chromax.black | NA-SEC1 chromax.black | NA-SYC1 chromax.black | |
| Explore other products from our chromax range: | 120mm black fan with PWM control | 140mm black fan with PWM control | Black anti-vibration pads for 120/140mm fans | Black anti-vibration mounts | 30cm fan extension cables, black | 4-Pin Y-cables, black |