8 Pack Strip Disc Stripping Wheel - for Angle Grinders Remove Rust Paint Stripping Wheel Clean Coating Welds Rust Oxidation (4 x 5/8)

Got these for my right angle grinder - I have both a corded and cordless. Fit on perfectly. I used these to remove some rust from some mild sheet steel. Worked perfectly without being too aggressive. I would recommend. Good value for an 8 pack with regards to cost.

I got these thinking they were like the stripping pads I use with my drill, but these are meant for a grinder. My drill pads are just pads with a hole that you screw down an arbor. Those can be used on either side but applying flat is not possible because of the arbor screw. These wheels have a built-in backing and metal reinforced arbor hole in the backing plate. The downside is they can only be used on one side. The upside is I can use them as a flat stripper with my grinder. I have a HF grinder and found the hole in these fit the grinder but were too small to fit around the indent in the nut. Thus, the force of the grinder was simply on the metal reinforcement band of the stripping wheel. That being said, I had no issues when I used this to smooth down old mortar from removed tiles. They worked pretty well, and perceptibly seemed to not wear down as fast as my other wheels. However, they also started being less effective about half-way worn as the surface became smoother from grinding the mortar. But overall, I really liked using these better than a wheel on a drill.

Impressive. The grinding material seems to be glued or fused to the arbor plate. I need this type of glue for everything! With that said - the grinding material sticks well to the plate it is attached to which of course is important. And what is this grinding material? Description states high-strength wear-resistant fiber mesh and combines resin elastomer and high-quality black diamond. It certainly does the job and does it well. All you need is a light touch to start. Work smarter - not harder. The grinding material seems to be flexible yet sturdy. Takes some finesse to get it done right. I easily removed the rust from entire metal leg I show in the picture and the grinding disc showed minimal loss of material. These should last for quite a while. I used the blue for removing the rust because I believe the purple discs are for heavier jobs. This was magically answered in the question section - not the description. I had to tighten the grinding disc to my angle grinder by hand. My tightening tool does not reach into the depths of the disc because of the thickness of the grinding material. I wore gloves and turned the wheel with the grinders lock on until it wouldnt turn anymore. I am confident it is secure but will keep an eye on it. Reverse this procedure to remove the disc. It is a perfect fit for my tool. No material other than rust went flying. I thought the material might grind off but it was not noticeable at least. Eventually I am sure they wear down. It looks like they might even clog up but that will depend on the material you are grinding/polishing. Of course, always use eye protection and unplug your tool when changing wheels. I consider myself very aware of possible hazards but lost the tip of one finger years ago to a silly mistake. Luckily, I have nine more fingers that still work fairly well. Always be safe. The product appears sturdy and well built. Very well built. These will make some hard jobs easy. A must have for the toolbox. They are a great value for an eight-pack. Neat product.

Was welding up some brackets using steel I had laying around in the garage. It had obviously oxidized much over the years so I needed to clean it up. These stripping wheels made quick work of cleaning the surfaces so I could weld them up.

I used one of these to clean an old shovel that was covered in rust, dirt, concrete and old paint. The stripper pads cleaned down to shiny metal in no time. The pad left a smooth shiny surface that is ready to prime and paint. The removal was fast but the pads did not leave deep scratches. These do not fall apart and last a long time. I really like these items and they are price reasonably.

I am pleasantly surprised that these abrasive stripping wheels as they lasted as long as they did. I am grinding and stripping of old welds on a project and needed some stripping wheels. I see these available and at a great price and thought it would take four or five of them to complete my job. Here I am, only used one of the wheels and my job is complete. I have a H. Freight 4 special grinder using the 5/8 arbor. This is some tough mesh and resin they used for these wheels. I used the wheels on 2024 Aluminum with about a 47 hardness and they worked great and didnt damage the material. I also used the wheels on 310 Annealed stainless steel with no problem. It was able to cut out with ease. 5 stars to WMAZtool for their TOUGH Stripping Wheels! Thanks :)

I use these stripping discs on my angle grinder to remove paint from an old truck I am refinishing. These discs are doing a great job and holding up well. I wish I knew what grit they were since it isnt listed but these discs work so well that I still gave them a 5-star rating.

These work well enough for surface prep for removing rust and old paint prior to welding and priming, however, there is zero indication as to what grit these are.

Got these for my right angle grinder - I have both a corded and cordless. Fit on perfectly. I used these to remove some rust from some mild sheet steel. Worked perfectly without being too aggressive. I would recommend. Good value for an 8 pack with regards to cost.

Ive never used this style of disc before, only flap wheels. I gave it 3 stars because I had a problem with it fitting on my corded Milwaukee. The thickness of the wheel was too deep for any spanner wrench I had, except for this universal spanner that thankfully would barely tighten the plate. So right away, the disc removed metal no problem. For reference, I used it to remove rust from angle iron before welding, and it did quick work of that. After that, I used it on a brand new outdoor griddle surface to remove the shipping oil, and to make the surface smooth. At first, it did a good job. After a while though, it seemed to get loaded up. When I stopped and looked at the wheel, it did have some melted surface area on it, about 10-20%. Im new to these strip discs, so maybe thats normal, maybe its not. It also embedded plastic into a few areas of my griddle top that then became nearly impossible to remove with sand discs, brake cleaner, denatured alcohol, etc. I pretty much had to burn it off during the seasoning of my griddle. Pros: They last a long time. Good value for the money. Less dust (I think) during rust removal. Cons: Disc was too thick for my spanner to fit on my Milwaukee, AND 2 other no-name grinders. they loaded up about 1/3 of their life.